North American Turbocoupe Organization



TFI MODULE WRENCH #FM-720A
Keith Nubel Offline
Posting Freak
#1
I just bought this tool - Kastar Hand Tools #FM-720A. It fits the screws for the TFI. It has a rachet, and it's offset. It's also in NAPA's catalog as #SER3410, the socket by itself is #SER3197. I can't download a picture, the board won't accept it, sorry.
1985 TC
Reply

Pete D Offline
Administrator
#2
Keith, we have the software set so that pictures cannot be imbeded on posts. However picrutes can be uploaded to the message board and a link(s) to it/them placed in a post.
Pete Dunham


Reply

evintho Offline
Senior Member
#3
Here's a pic of one I bought at NAPA. It was under $5 and works great!
http://natomessageboard.com/uploads/0000...FItool.jpg
Trust in the Lord with all your heart and lean not on your own understanding.
Proverbs 3:5

1986 Turbocoupe 5-spd - New daily driver!
1988 Turbocoupe 5-spd - parts car.
1989 Mustang convertible (Thunderstang). Built '88 TC shortblock, head by Boport, R/R, T3, Bobs log, gutted, rotated, ported mannys, AFPR, LA3, NPR I/C, etc.
Check out Thunderstang!
Reply

shays88tc Offline
Senior Member
#4
whats the P/N for that tool evintho?
Completion Date: Quarter to never..
Reply

shays88tc Offline
Senior Member
#5
ok N/M..im guessing the tool you have pictured has the same part # as in the first post?
Completion Date: Quarter to never..
Reply

evintho Offline
Senior Member
#6
shays88,
It has the NAPA logo on it and it's made by Evercraft Service Tools - P/N 775-9051. I'll bet you can probably get 'em at Kragen or Autozone too.
Trust in the Lord with all your heart and lean not on your own understanding.
Proverbs 3:5

1986 Turbocoupe 5-spd - New daily driver!
1988 Turbocoupe 5-spd - parts car.
1989 Mustang convertible (Thunderstang). Built '88 TC shortblock, head by Boport, R/R, T3, Bobs log, gutted, rotated, ported mannys, AFPR, LA3, NPR I/C, etc.
Check out Thunderstang!
Reply

sbhjr44 Offline
Senior Member
#7
I replaced my regular bolts with allen head bolts and now an allen wrench is all I need.
Stinger dual3"exhaust from dp & cat to magnaflows w/2.5 outlets w/tailpipes.Homemade CAI w/boost at18psi.MM c/c plates and tubular lca/front coilovers with Koni red adjustables all around. Ported/BV head/A237 and bobslog w/a stinger fmic set-up waiting to go on.86 stang gt w/motor and T-5 from a 86 TC w/3"SS dualexhaust w/cc plates and lowered 1.5".With volvo ic installed.
Reply

shays88tc Offline
Senior Member
#8
i suppose it would just be cheaper to swap out the bolts
Completion Date: Quarter to never..
Reply

gmaibach Offline
Senior Member
#9
wow i didnt know i could get a tool like that anywhere but the dealer. i just grinded a cheap socket... o well it worked and it was free.. nothin is cheaper than free
1988 Turbo Coupe 5 speed Red with Red cloth interior, K&N cone filter, Ported IHI turbo, ATR Header ported, Manual Boost Controller at 18 psi.

2013 Focus ST 2.0 Turbo, Buschur green filter, OCD Speed axle back exhaust.
Reply

86 XR7 5spd Offline
Senior Member
#10
LOL I had to "whittle" the plastic away from the TFI to get my 5.5 mm socket to sit in there deep enough

next time - theyre getting replaced with allen bolts Wink
David T
T5 / ported E3 / .63 / 35# / K&N
2.5" exhaust w/ cherry bomb
30+ mpg! 8.2 0-60, 16.4@88 1/4 (gTech)
Reply





Users browsing this thread:
1 Guest(s)



Theme © iAndrew 2018 - Software MyBB