mmedic50
|
Joined:
May 2001
Garrett, Indiana 46738
|
|
Has anybody tried getting with a business that does vinyl signs or graphics to see if they can make us an overlay for the center console and door locks that the lettering always seem to wear off of? If no one has tried this I will give it a shot this next week and let you guys know what I find out.
1988 TC 5 speed, Dark Blue
Build date 5/88.
140 mph Ford Motorsport Speedometer
Tripminder
Walbro 255 Fuel Pump
Kirban Adj. Fuel Pressure Regulator
K&N Air Filter
Gillis Boost Control Valve
New rebuild- .030 over pistons.
SS valves(1.89/1.59).
Center Force Stage II clutch.
ARP head studs.
Crane roller cam .450 lift.
Gutted upper and ported lower intake.
Ceramic coated and ported E6 exhaust.
|
Pete D
|
Joined:
Apr 2001
Northern OH
|
|
I know a lot of us would like to have fresh overlays. please give it a shot.
------------------
88 TC X 2, 86 SVO, Main TC with K&N, 3"DP to 2.5"duals through Dynamax, Ric valve at 17+ and disconnected KS.
Elite Bodega 16" chrome wheels. Autometer pod w/ A/F and Vac/boost gauges. New engine shortly, ported head and
manifolds, polished and cc'd chambers, A-230 cam, Race Engineering Adj Cam Sprocket, Crowlers, ARP head studs, Walbro 190 pump and T-3 for starters. KB subs
and jack rails.
Pete Dunham
|
plkdb
|
Joined:
Apr 2001
Gibsonia, PA USA
|
|
I havent seen anyone that does as of yet, so what I was actually planning on doing was theres a company called select products, they sell all types of car audio installation products, and they have sheets of carbon fiber overlay, burlwood, brushed aluminum, etc. I grabbed an extra set of the dash bezel and radio trim, and door switches, and am going to use them as templates for a carbon fiber set. They have the real stuff on their site, and they have simulated. The fake stuffs quite a bit cheaper!
|
Dan E
|
Joined:
Apr 2001
Greensboro, NC
|
|
Glad I'm not the only one ! Mine was so bad (overlay and paint) I just repainted the whole thing...now I could sure use the overlay. Let us know...I'll take one too.
------------------
88TC 5spd, Shortblock with Crower 5.5" Sportsman Rods and Short Wiseco Pistons bored .030" Over, Ported Head with Polished Combustion Chambers, Gutted & Polished Upper, Ported & Polished Lower, Polished T/B, Ported E6, SVO T3 Turbo, 3" DP w/No Cat, RR Cam, Adjustable Cam Sprocket, K&N in Fenderwell, Gillis Boost Valve, Centerforce I Clutch, Removed A/C, Polished Wheels, Polished Valve Cover, Polished Crank and W/P Pullies, and the DAMN Heater Core is new too !
[This message has been edited by Dan E (edited 05-26-2001).]
Dan Eaves
88TC 5spd Vermillion Red, Polished...everything...
|
plkdb
|
Joined:
Apr 2001
Gibsonia, PA USA
|
|
Dan, the website is www.selectproducts.com They sell sheets of the stuff, not kits for individual cars. If you go to their site, click on the big logo, then select products, then ABS laminates. I`m going to go with the carbon fiber, the sheets are 21.00 for a 12x24" sheet, and 52.50 for a 24x48" sheet regardless of the style.
|
