North American Turbocoupe Organization



car is a PITA.. 87 tc
Pete D Offline
Administrator
#11
IRCM schematic: http://turbotbird.com/techinfo/New_IRCM/schematic.html
Pete Dunham


Reply

turbo_crazy Offline
Senior Member
#12
always make sure the o2 wire is grounded when i'm under the hood.. with the RCM buzzing, i'm second guessing myself on what wiring i've pulled.. i'm hoping and praying i've accidentally pulled something i shouldn't have and i can just slip it back into place and be ok.. here's to hoping..
87 TC: 5spd, started B234F head swap (overall setup changing), Quarterhorse, T3/T4 63 a/r, 3" exhaust, walbro 255, tubular front clip, 5 lug swap, 17x8 front/17x9 rear cobra r's, wilwood 4 piston calipers (rear only, for now), lightened 471lbs so far
Reply

turbo_crazy Offline
Senior Member
#13
and thank you pete.. maybe i'll be able to figure something out if i use that diagram.. kind of odd that it occurred only after pulling the wires.. i had the key to the 'on' position numerous times before pulling the wires and it never buzzed
87 TC: 5spd, started B234F head swap (overall setup changing), Quarterhorse, T3/T4 63 a/r, 3" exhaust, walbro 255, tubular front clip, 5 lug swap, 17x8 front/17x9 rear cobra r's, wilwood 4 piston calipers (rear only, for now), lightened 471lbs so far
Reply

turbo_crazy Offline
Senior Member
#14
oh.. and my factory fan circuit is garbage, so no telling if the fans would be running or not
87 TC: 5spd, started B234F head swap (overall setup changing), Quarterhorse, T3/T4 63 a/r, 3" exhaust, walbro 255, tubular front clip, 5 lug swap, 17x8 front/17x9 rear cobra r's, wilwood 4 piston calipers (rear only, for now), lightened 471lbs so far
Reply

turbo_crazy Offline
Senior Member
#15
pete, dp you have a wiring diagram for the plug/harness that runs into the control module, as well? that'd be a big help in tracing everything, to make sure i didn't make a booboo.. i may have snipped a ground wire or something by accident, but not 100% sure
87 TC: 5spd, started B234F head swap (overall setup changing), Quarterhorse, T3/T4 63 a/r, 3" exhaust, walbro 255, tubular front clip, 5 lug swap, 17x8 front/17x9 rear cobra r's, wilwood 4 piston calipers (rear only, for now), lightened 471lbs so far
Reply

Pete D Offline
Administrator
#16
Check your email
Pete Dunham


Reply

Pete D Offline
Administrator
#17
Never mind, it bounced. I need a valid email.
Pete Dunham


Reply

turbo_crazy Offline
Senior Member
#18
it's been a while since i've used that email.. Try [email protected] .. Thanks pete
87 TC: 5spd, started B234F head swap (overall setup changing), Quarterhorse, T3/T4 63 a/r, 3" exhaust, walbro 255, tubular front clip, 5 lug swap, 17x8 front/17x9 rear cobra r's, wilwood 4 piston calipers (rear only, for now), lightened 471lbs so far
Reply

Pete D Offline
Administrator
#19
Done
Pete Dunham


Reply

turbo_crazy Offline
Senior Member
#20
awesome, THANKS!
87 TC: 5spd, started B234F head swap (overall setup changing), Quarterhorse, T3/T4 63 a/r, 3" exhaust, walbro 255, tubular front clip, 5 lug swap, 17x8 front/17x9 rear cobra r's, wilwood 4 piston calipers (rear only, for now), lightened 471lbs so far
Reply





Users browsing this thread:
1 Guest(s)



Theme © iAndrew 2018 - Software MyBB