RDOG
Joined:
Jun 2001
Ontario. California U.S.A.
|
|
Does anyone know where to get dew wipes for a 1986 TC. Mine are brittle and cracking.
1986 Turbo Coupe. Boport StageIII head, Boport 2.1, Performance Techniques 50 trim hybird, StageII.63, stinger 3" exhaust, Phenolic spacer, Boglog header,NPR FMIC intercooler setup, kirban fpr, bigrmotorsports fuel rail, diablo water meth kit, CAI, remote mount TFI, CHE rear adj control arms, MAC girdle, 8.8 rear disc, aluminum drive shaft, H&R lowerings springs Tbird Turbo Specific, y MAS!!
|
Robert Camp
Joined:
Jan 2006
Raleigh, NC
|
|
When you find suitable ones be sure and post it here.
Robert Camp
'86 Medium Regatta Blue TC, 5-speed, original owner.
|
RDOG
Joined:
Jun 2001
Ontario. California U.S.A.
|
|
I read your post back on 2006 in which you made a pair work. What happend to that supplier?
1986 Turbo Coupe. Boport StageIII head, Boport 2.1, Performance Techniques 50 trim hybird, StageII.63, stinger 3" exhaust, Phenolic spacer, Boglog header,NPR FMIC intercooler setup, kirban fpr, bigrmotorsports fuel rail, diablo water meth kit, CAI, remote mount TFI, CHE rear adj control arms, MAC girdle, 8.8 rear disc, aluminum drive shaft, H&R lowerings springs Tbird Turbo Specific, y MAS!!
|
Robert Camp
Joined:
Jan 2006
Raleigh, NC
|
|
Well, that was Russ C and I don't remember why but I didn't get them at the time.
Robert Camp
'86 Medium Regatta Blue TC, 5-speed, original owner.
|
etc1006
Joined:
May 2005
Baltimore, MD
|
|
I've been scouring the P&P for something with the same profile that I can remove and put on the exsisting molding on my SVO for now til i can get the repops for it. I have to replce my door glass they are so hard that they hve scratched it... I pulled inner ones from and aero mustang to put on my door panels as they are fried too (It spent its whole life in AZ) The TC uses the same profile I have a left door one in some of my old TC parts that is fried and I looked at it...
-Eric
|
HCOR
Joined:
Jul 2009
FOREST HILL MD
|
|
JC Whitney has the replacment dew wipes, I don't remember the part number off hand
only memories
|
etc1006
Joined:
May 2005
Baltimore, MD
|
|
Are these the ones you're thinking about?
http://www.jcwhitney.com/inner-and-outer...633y1985j1
or
http://www.jcwhitney.com/inner-and-outer...633y1985j1
I'll have to dig out my peice of dewipe and see how close a profile they have.
-Eric
|
HCOR
Joined:
Jul 2009
FOREST HILL MD
|
|
No I think we used this one, youwill need two for the outside and cut to fit.
http://www.jcwhitney.com/inner-and-outer...id=c3813j1
only memories
|
etc1006
Joined:
May 2005
Baltimore, MD
|
|
LOL I edited/posted the full listing of all the different profiles at the same time!
-Eric
|
RDOG
Joined:
Jun 2001
Ontario. California U.S.A.
|
|
Could I take the ones off a lincoln mark VII and cut them shorter?
1986 Turbo Coupe. Boport StageIII head, Boport 2.1, Performance Techniques 50 trim hybird, StageII.63, stinger 3" exhaust, Phenolic spacer, Boglog header,NPR FMIC intercooler setup, kirban fpr, bigrmotorsports fuel rail, diablo water meth kit, CAI, remote mount TFI, CHE rear adj control arms, MAC girdle, 8.8 rear disc, aluminum drive shaft, H&R lowerings springs Tbird Turbo Specific, y MAS!!
|
|